«ANGLER PRO 5.0» - Professional fish cutter

+7 985 922-58-88


Angler PRO 5.0
Профессиональный рыболовный катер Angler PRO 5.0

Angler PRO 5.0 professional fishing motor boat

  • Innovative materials and manufacturing technologies.
  • Optimum combination of seaworthiness, stability, dynamics and comfort.
  • Safety on water and usage pleasure during both fishing and hunting, and journeys.

Motor boat, intended to accommodate four passengers, is characterized by high finishing quality and
excellent ergonomics. If you like to fish in the sitting position, you may install chairs on the bow and stern using special consoles, which makes fishing more comfortable.

Boat perfectly sails across the wave due to its hull configuration, it has a wave-shearing bow and almost
flat bottom, high stability and increased level of safety.

Boat is designed specially for fishing, so it is equipped and furnished with regard to this specific field of application.
Front working deck is covered with special nonskid carpet.
A double-circuit aerator for 75 litres with lighting is located near consoles.

Hydraulic motor turning control ensures excellent boat manoeuvrability.
A lot of lockers and compartments, located along the whole boat length, allows to take everything you need,
and a lengthwise locker is intended for fishing rods storage.

Technical specifications of Angler PRO 5.0

Hull material glass-fibre plastic
Length, (m) 5.05
Width, (m) 1.95
Hull draft, (m) 0.35
Navigation area complexity category IV grade III
Transom height, (mm) 508
Deadrise angle on transom, (degrees) 14°
Built-in fuel tank capacity, (l) 135
Recommended engine power, (hp) 40 – 100
Passenger capacity, (persons.) 4
Additional cargo, (kg) 150
Weight of complete boat with outboard motor, (kg) 920

Basic configuration

Exterior

  • Removable chairs (with possibility for installation on front and rear decks)
  • Slots for chairs installation in front and rear decks working zones
  • Aerator for 75 l.
  • Dry locker for spinning rods
  • Additional dry lockers - 7 pcs.
  • Special coating on bow and stern working decks

Interior

  • Removable chairs (with possibility for installation on front and rear decks)
  • Slots for chairs installation in front and rear decks working zones
  • Aerator for 75 l.
  • Dry locker for spinning rods
  • Additional dry lockers - 7 pcs.
  • Special coating on bow and stern working decks

Electronics and control

  • Navigation lights (two on-board and one
    on stern)
  • Steering control (cable)
  • 12 V sockets - 2 pcs.
  • Battery disconnect switch
  • Fuse block
  • Electric equipment control buttons
    - 8 pcs.
  • Bilge pump
  • Electric horn
  • Cockpit lower part lighting
  • Fuel tank for 135 l.
  • Built-in filler neck

Optional equipment

  • Outboard motor(up to 90 hp)
  • Gas and reverse control
  • Hydraulic steering control
  • Starter accumulator battery
  • Service accumulator battery
  • Navigation awning set with arcs and fittings
  • Awning for transportation and storage
  • Removable mats in cockpit
  • Sleeves for fishing rods
  • Fathometer/map plotter/navigator
  • Instrumentation set:
    tachometer, speedometer, voltmeter, fuel level gauge,
    trim gauge, hour meter
  • Audio system (in marine version)
  • Watertight audio system cover
  • Acoustic system (in marine version)
  • Stainless steel bow (stem) protection
  • Polyurethane keel protection
  • Electric-driven anchor winch
  • Anchor
  • Park light
  • Trailer

Special design and technological solutions applied for SHUPER boats production

In order to improve navigation characteristics, stability, steerability, safety and seaworthiness in general, special and unique hull geometry is developed, adapted for operation both in shallow water and in open water.
Boat hulls are made from high-strength structural glass composite using proprietary binding agent having high impact toughness, strength and endurance.

Reinforcement diagram is developed on the base of strength calculation with double and, in some components, with fivefold strength margin.

Only proprietary high-quality resins and gelcoats are used in boats manufacturing.
Wall thickness of the hull lower part is 8 mm throughout the hull!

Frames and stringers are equipped with rubber-polymer pads ensuring soft and noiseless hull parts contact.

All hull and deck parts are moulded from high-strength structural glass composite.
Floatability (unsinkability) modules are made not from polystyrene foam (foamed plastic) pieces, but moulded from special Swiss Lloyd certified foam material with minimum 5% water absorption.
At that, double reserve of floatability is provided, on the basis of maximum possible boat design load.
Floatability modules also serve as sound insulation and lower small hull vibrations ensuring comfortable smooth movement across the ripple and wave.

Built-in fuel tank (135 l) is located practically in the middle for boat balancing optimization.
Only professional-grade stainless marine-type fasteners, materials and electric accessories are used for boats assembly .
Boats are equipped with bilge pump operating both in automatic mode (in case of water collection in the bilge in the amount of over 12 litres) and at forced switching-on from control panel.

Only certified highest quality instrumentation and components are used for boats equipment.
Decks and cockpit are equipped with special nonskid coating, stationary fastened or removable mats.
Keel is protected with special shockproof and wear-resistant polyurethane shield.
Stem is reinforced and protected with stainless steel shield.
All manholes are mde in dry execution.
All covers, awnings and other apparel are manufactured at the SHUPER factory, which ensures their highest quality and optimal fitting.


Production of SHUPER motor catamarans, electric E-Motion boats and crafts.
© «Company ASTER» LLC 2018.

ООО "Компания АСТЕР"
ул. Кулакова, д. 20, корп. 1 123592 Россия, г. Москва
+7 985 922 58 88, info@katamaran.com